EPMA Excellence in Powder Metallurgy Awards 2008

Winners of the EPMA’s 2010 Excellence in Powder Metallurgy Awards. The winning entries highlighted the capabilities of powder metallurgy and demonstrated the continuing advancements in the PM industry.

< See award archive

 

Components Category – Award of Merit

Brake Band Components

EPMA Excellence in Powder Metallurgy Awards 2008These components produced by Schunk Sintermetalltechnik GmbH, Germany, were presented with an ‘Award of Merit’ in the Components Category. The parts are used in manual seat-height adjustment devices in cars (Fig. 1). With a total of five other uniaxial compacted PM components, a set of two brake bands are fitted into each adjustment unit. It is precisely the narrow tolerances of this component, with a thinnest wall thickness of less than 2mm and an outside diameter of 53mm, which pose a big challenge for PM processing technology. Furthermore, high tolerance demands are placed on the evenness of the component, amounting to 0.2mm with the total height of the part being 4mm. The manufacture of several million such components in compliance with the tolerance demands a carefully controlled and fully linked production process.

 

Components Category – Highly Commended

MIM Planetary-Carrier with Sun Gear

EPMA Excellence in Powder Metallurgy Awards 2008Parmaco Metal Injection Moulding AG, Switzerland, were ‘Highly Commended’ in this category for their MIM planetary-carrier with sun gear (Fig. 2). The company stated that its customer was looking for a method to produce cost efficiently some 12 million high torque Planet-Carriers with Sun Gear for its high volume requirement of planetary gear boxes, with an outer diameter of only 6.2mm. These Planetary-Gear-Boxes are intended to be used in an opening and closing mechanism for cellular phones. The most cost effective manufacturing route for the high production volumes proved to be MicroMIM because instead of assembling 5 parts, MicroMIM can produce the Planet-Carrier with Sun Gear in one part. Cost savings compared to traditional production techniques are in the range of 40% for this new application.

 

Components Category – Notable Entries

PM Components for Steering Column Adjustment

EPMA Excellence in Powder Metallurgy Awards 2008Also entered in the Components Category and produced by AMES SA, Spain, were five PM parts (Fig. 3) which are assembled in the steering column of passenger cars and are the essential core of the steering wheel adjustment: up-and-down and in-and-out. Because of the ability of PM to generate complicated shapes, the customer can integrate the whole function in five parts, by designing directly with PM. Only a CNC multiplate press is able to generate the desired shape of the needle drive and the mobile rack. Heat treatment is mandatory because wear is prohibited and the parts are sliding between them in dry conditions. The teeth are very precise, in order to reach a smooth movement. Hardness is also critical with an HRC of 35. These components were introduced in 2007 and are produced at a rate of 1,500,000 parts per year.

 

MIM Stainless Steel Clock Housing with Brushed Surface Effect

EPMA Excellence in Powder Metallurgy Awards 2008Another entry in the Components Category was this stainless steel MIM clock housing developed by OBE Ohnmacht & Baumgärtner GmbH, Germany, and used in a high-end automotive dashboard (Fig. 4). The company states that the reason for using MIM was to achieve perceived high value and a cool touch by replacing the original metalised plastic material. Using Catamold Feedstock 316L and with a weight per component of 13.6g the items are produced in a one cavity mould. A special feature is that the brushed surface effect is already integrated into the tool. This is an example of where MIM components can be economic when produced only in low quantities due the high value of the item.

 

Materials and Processing Category – Award of Merit

Ancorsteel® 30 HP

EPMA Excellence in Powder Metallurgy Awards 2008In the Materials and Processing Category the EPMA presented the ‘Award of Merit’ to Hoeganaes Corp., USA, for its Ancorsteel® 30 HP. The water-atomised, prealloyed low-alloy steel powder is specifically targeted at high performance applications and has reduced amounts of the expensive alloying elements, such as Ni and Mo (Fig. 5). The new powder is said to be particularly suitable for Quench and tempered PM parts with smaller cross section sizes where it enables similar heat-treated strength and hardness properties to be achieved as in traditional Mo-prealloyed powders.

 

Materials and Processing Category – Highly Commended

Improved Corrosion Resistant Stainless Steel Alloy – STX2000

EPMA Excellence in Powder Metallurgy Awards 2008Sintex A/S, Denmark, were ‘Highly Commended’ for a recent development project aimed at producing a new sintered stainless steel alloy with more stable microstructure, higher corrosion resistance and reduced amount of alloying elements (Fig. 6). Molybdenum content was reduced from 6.5% to 3.9%. However, further optimisation was needed in the manufacturing processes to maintain a high level of corrosion resistance particularly in the compaction process and more importantly in the sintering process. As a consequence a new sintering furnace with focus on atmosphere and temperature control was designed and developed. The results were outstanding: an accelerated salt spray test of the new alloy has shown significantly better corrosion resistance than the old STX1000.

 

Materials and Processing Category – Notable Entries

Starmix BOOST powder mix

EPMA Excellence in Powder Metallurgy Awards 2008Another entry in the Materials and Processing Category included Höganäs AB, Sweden, who developed their Starmix BOOST bonded powder mix. A new innovative lubricant and binder system, in combination with a special powder treatment process, results in mixes having much improved performance (Fig. 7).

 

In the latest issue of PM Review…

Download PDF

Extensive Powder Metallurgy industry news coverage, and the following exclusive deep-dive articles and reports:

  • From powder modification to rejuvenation: Fluidised Bed Reactors in metal powder production and Additive Manufacturing
  • Retech: Enabling the atomisation of reactive and refractory alloys at substantially higher levels of productivity and lower cost
  • Sustainability in Powder Metallurgy: Highlights from the 41st Hagen Symposium
  • Innovations from Japan’s Powder Metallurgy industry: award winners highlight novel automotive and healthcare applications

The latest news from the world of metal powders, delivered to your inbox

Don't miss any new issue of PM Review, and get the latest industry news. Sign up to our weekly newsletter.

Sign up

Join our community

Discover our magazine archive…

The free-to-access PM Review magazine archive offers unparalleled insight into the world of Powder Metallurgy from a commercial and technological perspective through:

  • Reports on visits to leading PM part manufacturers, metal powder manufacturers and industry suppliers
  • Articles on technology and application trends
  • Information on materials developments
  • Reviews of key technical presentations from the international conference circuit
  • International industry news

All past issues are available to download as free PDFs or view in your browser.

 

Browse the archive

 

Looking for PM production equipment, metal powders, R&D support and more?

Discover suppliers of these and more in our
advertisers’ index and buyer’s guide, available in the back of PM Review magazine.

  • Powders & materials
  • Powder process, classification & analysis
  • PM products
  • Atomisers & powder production technology
  • Compaction presses, tooling & ancillaries
  • Sintering equipment & ancillaries
  • Post-processing
  • Consulting & toll sintering
View online
Share via
Copy link